Well after a long wait I decided to release instead of waiting to release.
It has six ties between the stops. becareful with the front hook it can break.
F1-F2 raise lower hook (Hook is also a contact so raise it before backing)
F3-F4 open control panel on the side.
F5-F6 raise lower axles
F7-F8 raise lower axles
F9-F10 raise lower axles
F11-F12 raise lower back ramp.
This has no dolly trailer this time. It is hard on the framerate too.
Next version will probably use hookgroups to make more solid.
Max capacity is 25 tons. I will also try to reduce axles next time.
Hello. This Is my flatbed. Nothing really special. Just a grey trailer with submesh, ramps, and ties. Thanks to Squatch for submeshing and maxmillion for betatesting.
1/2: Lower/Raise Jacks
5/6: Raise/Lower Ramps
1: Get a semi of your choice and spawn the trailer
2: Raise Up the jacks and hook up to the trailer
3: Lower jacks and ramp
4: Get a car of your choice and drive on the trailer
5: Get in the truck, press O
6: Raise ramps and drive away
This a Orion WH115 bus-trailer.
Doors open/close with F5/F6.
-simple texturing possible
-"Army" (fitting to the same version of the bus)
-"Travel Coventry" (fitting to the same version of the bus)
-"A B Bruch" (this trailer was build after a 1/87 scale model... this is like the one I have as a model)
This trailer was build to fit to pr14sl's S53R V2. To make it have a trailer hitch, please replace this line in the .truck-file:
"111, 11.475, 0.422, 1.25"
with this line:
"111, 11.6, 0.35, 1.25, h".
pr14sl - some parts of "Travel Coventry"-textur and help
Lenni - wheelbands
BigBoy - everything else...
Ackermann Moving Trailers
Here are my moving trailers for both the Buessing and the Mercedes Moving Vans.
They have managed materials and material-flares, and are useing sections.
They're not loadable... just some nice trailers to pull around.
here is my second upload on the repo:
A 300 ton Heavy Haul LowBoy trailer.
I made the 3d-model some time ago, now I put it into RoR with some overwork.
You can change the color by editing the "300tlb_color.jpg" and the color of the wheels by editing the "300tlb_wheelcolor.jpg".
It has only five invisible wheels, this means it works very smooth even on lower systems (and that is actually the reason why I "cheated" ;-) ).
Use F3/F4 for the (invisible) trailer legs under the first part.
With F1/F2 you can rotate the steering dolly to the left and right. As far as I know this is done via hydraulic in real life. In fact it is just like a semi, but not propulsed.
It is loaded with a big tube.
Have fun driving it (and don't forget to look after the steering dolly ;-) ).
This my Goldhofer STNL3-Platform trailer "Speedy".
"Speedy" is a very flexible and light platform trailer.
CTRL+ALT+F1/+F2: lower/raise trailer legs
CTRL+ALT+F3/+F4: lock/unlock steering (lock for reverse driving or extending trailer/steering is locked when trailer spawnes)
CTRL+ALT+F5/+F6: extend trailer
CTRL+ALT+F7/+F8: raise/lower liftaxle
CTRL+ALT+F9/+F10: raise/lower trailer ramps
Note: All commads exept ramps are one-press-commands.
Hope you like it :-)
This is my Huge Enclosed trailer. It can fit the liebber, that should tell how big it is. It's also only 34 nodes, so Fps are great with it. You have to really try to roll it over, so it has a great center of gravity. Has working flares, ties, feet, and ramp, so u can drive pretty much any vehicle in and strap it down.
Included in this pack are:
1)Gooseneck Enclosed Trailer
2)Bumper Pull Enclosed Trailer
Here's a trailer I made awhile back with a detaching Neck. It can haul some big stuff, has a flexbody deck that bends flat with a heavy load and flexes over bumps. Its not all that finished, but its as finished as its gonna get, lol. I made a video to show how to use it
Ctrl F1 to raise the neck so you can back under and lock on
Ctrl F2 seats the neck on the hitch after you locked on
Ctrl F3 attaches neck to the trailer
Ctrl F4 detaches neck so you can drive it out of the way to load/unload
Here is my first mod i made all on my own. It doesn't have a contactable submesh, because people who said they would do it didn't. It is still a beta, however, i want more people to test for further problems. Once i can move around some nodes here and there and get everything just right, then it will be ready for a final release. Check out the thread for it, i need feedback here and there for my trailer. Hope you guys have fun hauling this around when you are bored. Happy holidays!
This is my modded virsion of the sliding flatbed i modded a while back so i finally wanted to mod and make it better. it works like and actuall landoll trailer. have fun and keep the wheels about where i have them in the picture cause if u go any further it will break, also keep ur parking brake off to move the wheels. this is a trailer
dolly legs: f1 f2
wheels forward and backward: f3 f4
up and down: f5 f6
A modified short dump trailer. Originally made by Trevor, this new trailer, has a more common paint job, along with American style rear wheel rims. It has emissive with dot strips. These dump trailers are used in the industry for hauling demolition debris, dirt, aggregate, waste, etc. It works for both 0.35 and 0.36. Everything works except the mini file .
Kenworth Transfer Dump Truck
A transfer dump truck inspired by a request on the forum.
Credits go to Box5Diesel for his Kenworth truck.
For information on how the system works see the request and showrooms thread.
Feel free to modify, but use a different unique id to make it not conflicting with my truck.
Skins for Box5diesels Kenworth should work on this truck, but I'm not sure.
I've fixed a little bug with the material of the trailer dump box.
This is the Mercedes Benz Actros 8x8 pack.
This package includes 8 versions:
- version with no upper part
- cartransporter (+trailer)
- log truck (+trailer NEW!)
- box-truck(+trailer NEW!)
- flatbed (+trailer NEW!)
This is a mobile home or mobile office depends on how you use it. You can pull it to your location and pull the tires into the body and it will be on the ground like a house. It is a decent amount of weight 22046.23lbs. It is fun to pull around comments are greatly welcomed. This is a 10x40 trailer its not a CAMPER.
made by me
Update 1. made the tongue longer fixed the tires problems added more weight
This is a simple small bumper pull camper. It is my second camper i have made. This one is a little unsteady when going over 60. And the one with extra weight on the tires sways sometimes. I will continue to fix these problems though. The normal non weighted one does roll sometimes.
New versions of the dump trailers because of problems with the original one.
Long dumper (3 axle), long dumper with dolly (4 axle), short dumper (2 axle), and short dumper with dolly (4 axle).
They all have lights now.
F1/F2 for the legs on the long and short dumpers.
F3/F4 to raise/lower the bed on the long and short dumpers.
F5/F6 to raise/lower the bed on the trailers with dolly.
F7/F8 to increase or decrease the distance between the trailer. (so you can move them further apart, back up at an angle, pretend to empty the first dumper without disconnecting them)
They are set up as normal trucks, so their engines must run for the commands to work. I tried it with the turboprop thingy from the original version but RoR kept crashing untill I removed them. :-(
The trailers with dolly also have a hook in the back, so you can chain them together if you want.
Also included is a new frameless dumper. It is based on the old one, but it has a new a-arm, new legs, new dump bed, lights and mapped to the same texture as the others.
There are some trailers that can be hooked behind eachother to make a roadtrain, but they can lower your framerate a lot.
These trailers are made from as few nodes as possible to keep framerate up. The downside is that they do not have a lot of details. (no lights, no contacters, no props)
Two versions are include, a set of 3 and a set of 5 trailers. Both can be entered (like a truck) and have a 5th wheel in the back to hook up more trailers.
48 Foot reefer with spread axle.
Made from some pictures send to me (and some imagination), colors are matching the Peterbilt 359.
F1/F2: Raise/lower the legs
F3/F4: Raise/lower kingpin a bit. I added this because sometimes the trailer got stuck in the truck wheels. That chance is reduced by not tagging 2 polys as contactable on the trailer.
A 3-axle refrigerated trailer, modified from the spread axle reefer.
F1/F2 to raise or lower the legs
F3/F4 to adjust kingpin height a bit (to avoid rear truck wheels getting stuck in the trailer textures)
Feel free to modify, and a skin-template is included.
I turned the cement truck into a trailer by removing the cab and the 2 front axles.
The drum is enlarged to fit the frame, total length is only 8 meters/27 foot and it weighs 20 tonne.
Despite having the load nodes at the bottom of the frame, it still want to tip over.
Known bug: Because the drum is stretched, at a slightly different angle (7 degrees instead of 9 on the truck) and rounding the coordinates, it is not balanced.
It's rotation alternates left and right. You can use the mouse to give it a swing, but then it seems to gain rotating speed and makes everything shake. (Looks funny, but makes it drive bad)
F5/F6: rotate chute
F7/F8: lower/raise chute
Trailer with an ampliroll hook, modified from the Volvo.
Removed the cab and the 2 front axles, and made a regular tow bar. Color is matching the Zetor Traktor.
You have to enter the trailer like a truck to connect the hook to the load, the wheels are still driven so you can move it forward and backward.
It has importcommand so it "listens" to the towing vehicle as well (if that has forwardcommands)
ctrl-F1/F2 for the legs
ctrl-F3/F4 for the tow bar height
ctrl-F5/F6 for the arm with hook
ctrl-F7/F8 for the dumping arm
ctrl-F9/F10 to tighten the ties (they sometimes only grab, but don't tighten)
Hello, I'm happy to introduce my first ever official mod to a trailer, It is a monster energy skin for the FEDEX 53ft Great Dane dryvan, Just throw it in packs, Because of the (1) at the end it will not overwrite, So enjoy, I hope it is a cool mod to you guys, It took about 3 hours to get it right... haha.
This is jerald9000's 53-foot Great Dane trailer, reskinned into the livery of my new trucking company, Dreamland Trucking. The blank area in the center of the sides of the trailers can be skinned to your liking. It should not overwrite the original trailer.
I was searching the forums recently, and discovered that there were no ramps to jump cars off of, so I decided to create one. This is a car-sized "Kicker" ramp based off of those that are used for skateboarding. It has a tow hitch so you can drag it around with trucks, so moving it is possible. It only weights 150 Kg, so most vehicles can tow it. As a side note, this is my very first mod for any game.
+Add more types of ramps, especially tilted ramps and sliced quarter pipe ramps.
+ Added New Twisted Ramp 'RoR Ramp "Twisted Kicker" - Plastic'
+ Added New Twisted Ramp 'RoR Ramp "Twisted Kicker" - Full Metal'
+ Renamed Original Ramp to 'RoR Ramp "Kicker" - Plastic'
+ Added New All Metal Ramp: 'RoR Ramp "Kicker" - Full Metal'
+ Full Metal ramp weighs more than Plastic ramp.
+ Plastic ramp is still compatible with people that still have V1
+ Fixed some errors.
[Moved Props section below nodes]
Everything was created by me.
To Modders of Mods:
I know who I personally have given permission to mod this, so don't mod without permission.
Link to Discussion: RoR-Ramp (More Frequent Updates)
Heavy vehicles or vehicles with large tires risk causing the ramps to slide. The ramps were designed for lighter vehicles and are physically designed to be light so they can be towed by normal vehicles such as SUVs or Pickup Trucks (Including the S10).