This my Goldhofer STNL3-Platform trailer "Speedy".
"Speedy" is a very flexible and light platform trailer.
Commands:
CTRL+ALT+F1/+F2: lower/raise trailer legs
CTRL+ALT+F3/+F4: lock/unlock steering (lock for reverse driving or extending trailer/steering is locked when trailer spawnes)
CTRL+ALT+F5/+F6: extend trailer
CTRL+ALT+F7/+F8: raise/lower liftaxle
CTRL+ALT+F9/+F10: raise/lower trailer ramps
Note: All commads exept ramps are one-press-commands.
Hope you like it :-)
Here's a trailer I made awhile back with a detaching Neck. It can haul some big stuff, has a flexbody deck that bends flat with a heavy load and flexes over bumps. Its not all that finished, but its as finished as its gonna get, lol. I made a video to show how to use it
Ctrl F1 to raise the neck so you can back under and lock on
Ctrl F2 seats the neck on the hitch after you locked on
Ctrl F3 attaches neck to the trailer
Ctrl F4 detaches neck so you can drive it out of the way to load/unload
Here is my first mod i made all on my own. It doesn't have a contactable submesh, because people who said they would do it didn't. It is still a beta, however, i want more people to test for further problems. Once i can move around some nodes here and there and get everything just right, then it will be ready for a final release. Check out the thread for it, i need feedback here and there for my trailer. Hope you guys have fun hauling this around when you are bored. Happy holidays!
This is my modded virsion of the sliding flatbed i modded a while back so i finally wanted to mod and make it better. it works like and actuall landoll trailer. have fun and keep the wheels about where i have them in the picture cause if u go any further it will break, also keep ur parking brake off to move the wheels. this is a trailer
Commands
dolly legs: f1 f2
wheels forward and backward: f3 f4
up and down: f5 f6
This pack is my attempt to capture the Streamline Moderne style popular in the 1930s and 1940s. The vehicles are all fictional, but their performance is realistic. I hope you'll enjoy driving them as much as I have enjoyed making them.
1948 Martin T64S "Custom" Tractor
A very low-slung 6x4 tractor. It has independent front suspension with double wishbones and load sharing rear suspension. The engine is a naturally aspirated 12-cylinder diesel driving through a 7-speed gearbox and locking differentials. Overall length is 29 ft, wheelbase 22 ft from front axle to centre of rear axle group, width 102 in, height 14 ft 9 in to tip of smokestacks. Kerb weight is 20,000 lbs, gross combination weight 80,000 lbs.
Fully loaded, the T64S will reach a top speed of 60 MPH with one of the included trailers. It will accelerate from 0-50 MPH in 1 minute, 0-60 MPH taking approximately 2 minutes.
1948 Martin O40 Tanker
A streamlined tank trailer in fictional "Hexaco" livery. Steel unibody, load sharing suspension. Overall length is 40 ft, wheelbase 28 ft from kingpin to axle group centre, width 102 in, height 10 ft 6 in. Loaded weight is 60,000 lbs.
1948 Martin F45 Flatbed
A simple flatbed trailer with stainless steel load deck and load sharing suspension. The deck is submeshed with the rollon flag and has ties to secure loads. Overall length is 45 ft, wheelbase 36 ft from kingpin to axle group centre, width 102 in, deck height 59 in, overall height 79 in to top of bulkhead. Kerb weight is 12,500 lbs, rated load 47,500 lbs.
1948 Martin V59 "Streamliner" Dry Van
A very large and somewhat impractical dry van. It has a streamlined stainless steel unibody and load sharing suspension. Overall length is 59 ft, wheelbase 47 ft from kingpin to axle group centre, width 102 in, height 14 ft 9 in. Loaded weight is 60,000 lbs.
Notes
These have only been tested in Rigs of Rods version 0.38.67.
The wheels have 40 nodes each, and the meshes were made in Sketchup. Don't expect these to be FPS-friendly.
The trailers are roll coupled via the system used by Lenni and Badboy for trailer steering. The centre of gravity and suspension are tuned accordingly; the trailers may topple easily on trucks that lack these nodes.
To minimise rolling resistance, the wheels are pushing the limits of the beam engine. They tend to oscillate when stationary. Caution is advised when stopping or parking on slopes as they may creep.
The trailers have very low drag. The T64S will not pull most other trailers at high speed.
Licence
CGTextures does not allow redistribution of its textures under open source licences. You must remove/replace their texture before releasing modifications of this truck. All other assets used are available for modding. See the readme for specific file information and licensing details.
This is a mod to box5's goose neck. I made it shorter and made it have two axles. The mod was simply to make it look better when hauling stuff around. In my opinion the normal one is a little large.
Original trailer is box5s
Mod by me
And i know the mod isn't perfect. May over write the old one.
Original file http://www.rigsofrods.com/repository/view/585#comments
A telecopic trailer based on OVB-55-03V(T) model from Nooteboom.
features and commands:
- can extend up to 40m (CTRL+F1/F2)
- manual steering (F7/F8)
- adjutable suspension (CTRL+F3...F8)
- drop sides, to prevent falling loads (CTRL+F9/F10)
- fully working ligths
- avaible in 3 colors: red/yellow/blue
All commands are written on the front left side of the trailer
goldhofer_stnl3.zip
view details
Gold
Silver
Bronze
