Here is my Hyster top spreader i made for the vast amount of growing containers RoR has acquired.
Thanks to my beta testers for feedback.
once spawned the hyster will bounce a little just press backspace and it will be fine.
to hook onto a container slowly drive to the center of the container and extend the spreader(the spreaders extends more than the container so you do not have to be dead center to hook onto the container properly)
Make sure all 4 ties are secured and lift with the engine reved.
There is a readme with the controls.
this is a project i will most probably never Finnish as i started something else instead.
its the 4x4 thing and a custom made crane trailer for it,
the 4x4 thing has 4 wheel steering at low speeds, locked diffs and a steering wheel.
the crane trailer has ropes and a invisible leg, the commands for it are are:
F9-F10 lower and lift the crane boom.
F11-F12 lower lift the invisible foot.
'O' connect load
'L' lock crane trailer to vehicle.
to connect the trailer drive the 4x4thing so the trailers hitch node is above the grease mark on the 4x4 thing and it 'L'
to pick up a load back the crane trailer over it lower it so its with in 1.5m from the object and it 'O' once it connects
and the ropes shorten hit F10 to lift the load of the ground and drive away. reverse order for dropping a load.
the crane trailer is usable on other 5th wheel hitches.
Mesh of the uppercabin is made by Craneman
Other mesh parts are made by me
N/B axles are made by Craneman
what you get is:
Terex-Demag ac500 with ssl
Terex-Demag ac500 without ssl
Terex-Demag ac500 with 18m fixed jib
Terex-Demag ac500 with 30m fixed jib
Terex-Demag ac500 with 36m luffing jib
Terex-Demag ac500 with 60m luffing jib
Terex-Demag ac500 with 90m luffing jib
controls:
f1 or f2 = turn left or right
f3 or f4 = boom up/down
f5 or f6 = hook up/down
f7 or f8 = cab up/down
f9 or f10=counterweight systeem up/down press K too see it
f11 or f12=jib up/down
ctrl+f1 or ctrl+f2=boom1 in/out
ctrl+f3 or ctrl+f4=boom2 in/out
ctrl+f5 or ctrl+f6=boom3 in/out
ctrl+f7 or ctrl+f8=boom4 in/out
alt+f1 or alt+f2 = suspension up/down
alt+f5 or alt+f6 = outriggers turn
alt+f7 or alt+f8 = outriggers in/out
alt+f9 or alt+f10 = outriggers up/down
alt+f11 or alt+f12=cab turn
ctrl+alt+f1 or ctrl+alt+f2 = axle 5 lift
ctrl+alt+f3 or ctrl+alt+f4 = ssl up/down
ctrl+alt+f5 or ctrl+alt+f6 = ssl sidemoving
ctrl+alt+f7 or ctrl+alt+f8 = ssl ropes ssl till boomhead
ctrl+alt+f9 or ctrl+alt+f10 =couterweight boom up down only by versions needed with luffing jib
ctrl+alt+f11 or ctl+alt+f12=crab steer
i hope i have write all commands
look at the first post of ac500 topic for pictures how the counterweight systeem work (demag-ac500)
Features
- Detailed meshes
- Accurate kinematics
- Realistic lifting capacity (refer to the board on the crane!)
Instructions
Start the engine and put the Crane in NEUTRAL!
- F1/F2: Rotate
- F3/F4: Trolley (use throttle to speed up if needed)
- F5/F6: Hook Up/Down (use throttle to speed up if needed)
- F7/F8: Extend/Retract Jib
- F9/F10: Raised-jib working angle
- Ctrl+F1/F2: Assemble/Disassemble
- Ctrl+F3/F4: Outriggers
- Ctrl+F5/F6: Legs
- Ctrl+F7/F8: Trailer wheel up/down
- Ctrl+F9/F10: Turn trailer wheel
- And as usual lock loads with "o"
You can also see the commands by pressing "T" ingame.
Basical procedure: Ctrl+F4 to fold outriggers; Ctrl+F6 once for legs, Ctrl+1 [NOT F1!] to display the baseplates, Ctrl+F6 again for legs. Then Ctrl+F2 to erect the crane automatically. Jib control is on F7/F8. Jib angle is on F9/F10. Retract automatically on Ctrl+F1.
Credits:
- sputnik_1: meshes, node and beam, sounds, textures
- BigBoy, Craneman, Lifter, Inviteds, Donators: testing and help, thanks a lot!
Rotexx-presseteil.zip
view details
Gold
Silver
Bronze
