This pack is my attempt to capture the Streamline Moderne style popular in the 1930s and 1940s. The vehicles are all fictional, but their performance is realistic. I hope you'll enjoy driving them as much as I have enjoyed making them.
1948 Martin T64S "Custom" Tractor
A very low-slung 6x4 tractor. It has independent front suspension with double wishbones and load sharing rear suspension. The engine is a naturally aspirated 12-cylinder diesel driving through a 7-speed gearbox and locking differentials. Overall length is 29 ft, wheelbase 22 ft from front axle to centre of rear axle group, width 102 in, height 14 ft 9 in to tip of smokestacks. Kerb weight is 20,000 lbs, gross combination weight 80,000 lbs.
Fully loaded, the T64S will reach a top speed of 60 MPH with one of the included trailers. It will accelerate from 0-50 MPH in 1 minute, 0-60 MPH taking approximately 2 minutes.
1948 Martin O40 Tanker
A streamlined tank trailer in fictional "Hexaco" livery. Steel unibody, load sharing suspension. Overall length is 40 ft, wheelbase 28 ft from kingpin to axle group centre, width 102 in, height 10 ft 6 in. Loaded weight is 60,000 lbs.
1948 Martin F45 Flatbed
A simple flatbed trailer with stainless steel load deck and load sharing suspension. The deck is submeshed with the rollon flag and has ties to secure loads. Overall length is 45 ft, wheelbase 36 ft from kingpin to axle group centre, width 102 in, deck height 59 in, overall height 79 in to top of bulkhead. Kerb weight is 12,500 lbs, rated load 47,500 lbs.
1948 Martin V59 "Streamliner" Dry Van
A very large and somewhat impractical dry van. It has a streamlined stainless steel unibody and load sharing suspension. Overall length is 59 ft, wheelbase 47 ft from kingpin to axle group centre, width 102 in, height 14 ft 9 in. Loaded weight is 60,000 lbs.
These have only been tested in Rigs of Rods version 0.38.67.
The wheels have 40 nodes each, and the meshes were made in Sketchup. Don't expect these to be FPS-friendly.
The trailers are roll coupled via the system used by Lenni and Badboy for trailer steering. The centre of gravity and suspension are tuned accordingly; the trailers may topple easily on trucks that lack these nodes.
To minimise rolling resistance, the wheels are pushing the limits of the beam engine. They tend to oscillate when stationary. Caution is advised when stopping or parking on slopes as they may creep.
The trailers have very low drag. The T64S will not pull most other trailers at high speed.
CGTextures does not allow redistribution of its textures under open source licences. You must remove/replace their texture before releasing modifications of this truck. All other assets used are available for modding. See the readme for specific file information and licensing details.
Many months in the working it's finally here
Various modified version made by me. all the ones with more than 2 axles, the 3rd axle is liftable and the ones with more than 3 axles the 4th and 3rd axle are liftable.
on the heavy haul versions with 4 axles only the front axle is liftable.the heavy haul versions can haul 200tons, mainly the 3axle and 4axle versions.
Kenworth T800W tri-axle Daycab longframe
Kenworth T800 daycab short frame
Kenworth T800 daycab short frame Tbox
Kenworth T800 4th axle Extended Flatbed
Kenworth T800 boxtruck 4th axle
Kenworth T800W toolbox tri-axle Daycab longframe
Kenworth T800W sleeper tri-axle longframe heavy haul
Kenworth T800 tilt Flatbed long frame 4-axle
Kenworth T800 dumptruck 4th axle
Kenworth T800W sleeper two-axle longframe
Kenworth T800 2 axle Extended Flatbed
Kenworth T800 sleeper Extended Flatbed tri axle
Kenworth T800 sleeper short frame
Kenworth T800 sleeper short frame Tbox bed
Kenworth T800W sleeper toolbox tri-axle longframe
Kenworth T800 sleeper Flatbed short frame
Kenworth T800 sleeper short frame heavy haul
Kenworth T800 Long frame Logtruck
Kenworth T800 longer Tanker
Kenworth T800 Extended Flatbed tri-axle
Kenworth T800W two-axle Daycab longframe
Kenworth T800 Daycab 2 axle shorter frame
Kenworth T800 two axle boxtruck
Kenworth T800 dump truck 2 axle
Kenworth T800W Daycab heavy haul tri-axle shorterframe
Kenworth T800 tilt Flatbed long frame Tri-axle
Kenworth T800 Tilt Flatbed regular frame
Kenworth T800W sleeper heavy haul 4-axle heavyframe
Kenworth T800W Daycab heavy haul 4-axle heavyframe
Kenworth T800 tri axle boxtruck
Kenworth T800 Flatbed short frame
Kenworth T800 terrain editor
Commands for the Various trucks that have liftable objects.
All truck have opening hoods F3-F4
Kenworth T800W tri-axle Daycab longframe F7-F8 for lift axle
Kenworth T800 4th axle Extended Flatbed F9-F10 for lift axle
Kenworth T800 boxtruck 4th axle F5-F6 for lift axle
Kenworth T800W toolbox tri-axle Daycab longframe F7-F8 for lift axle
Kenworth T800W sleeper tri-axle longframe heavy haul F7-F8 for lift axle F9-F10 for movable fifth wheel
Kenworth T800 tilt Flatbed long frame 4-axle F-7-F-8 to lift axles F9-F10 to lift bed F-11-F-12 to open tailgate
Kenworth T800 dumptruck 4th axle F5-F6 to open dump door F7-F8 to lift dump body F-9-F10 to lift axles
Kenworth T800 sleeper Extended Flatbed tri axle F7-F8 for lift axle
Kenworth T800W sleeper toolbox tri-axle longframe F7-F8 for lift axle
Kenworth T800 Long frame Logtruck F5-F6 to open invisible door so the logs don't fall out. press K to view skeletal mode
Kenworth T800 Extended Flatbed tri-axle F7-F8 for lift axle
Kenworth T800 dump truck 2 axle F5-F6 to lift dump body F7-F8 to open dump door
Kenworth T800W Daycab heavy haul tri-axle shorterframe F7-F8 for lift axle
Kenworth T800 tilt Flatbed long frame Tri-axle F7-F8 to raise axle F9-F10 to raise bed F11-F12 to open tailgate
Kenworth T800 Tilt Flatbed regular frame F5-F6 to raise bed
Kenworth T800W sleeper heavy haul 4-axle heavyframe F7-F8 for lift axle
Kenworth T800W Daycab heavy haul 4-axle heavyframe F7-F8 for lift axle
Kenworth T800 tri axle boxtruck F7-F8 for lift axle
-Real weight, real power, real scale. (so don't expect to tow the ror trailers that way a kabillion lbs.)
-Lockers (press W)
-Operational dump bed, & tailgate
-Contactable bed to load vehicles or objects with ties (press O to tie down load)
-Animated winches on all except cargo version, some even have a rear winch.
-Flexbody everything pretty much
-Detailed Animated Interior with shifter.
-custom deuce sounds, with added turbo
-Shader shows up black sometimes, restart ROR until it appears normal, or download boring material below and drop in deuce zip.
-5th wheel version breaks when hooking to some trailers
-No flexbody tires (would be way to cpu heavy, it already is)
This is a 1976 Ford W-9000 cab-over-engine semi tractor. A fairly basic node-beam vehicle that will get the job done. All of the pieces for this were created by me (M-138) except the mirrors. Feel free to modify, just remember to give credit.
This pack has four custom Kenworth T600's. They started as a joke but I got carried away. There is probably a lot of bugs and stuff I haven't found but I just wanted to get them finished.
Most of the trucks are completely impractical. The wheel base is too long to have a tight turning circle. They sit so low you'll rip your bumper off the instant you hit a gutter. The lowriders with hydraulics have the worst ride imaginable and are stiff as a rock. The only purpose they really serve is to look cool.
'L' to lock on a trailer
'N' for lights
'Ctrl+1' for headlights
'F4/F3' to raise and lower the hood
For trucks 2 and 3:
'F5/F6' for front hydros
'F7/F8' for rear hydros
Feel free to mod these or do your own bug-fixin' however you see fit.
-updated version, rope spreading works now and ballastbox sides don't lock up anymore-
-new update: wheel definition updated and new working mirrors added.
This is a pack with a semi version and a ballastbox version of this truck,
it also contains a jib which can be fitted to both versions.
After a very long time of making this truck it is finally finished,
it features a fully funcional crane,
animated parts like driveshafts and control levers
animated cockpit, lights all around the truck,
custom sounds and a contactable surface on the truck.
Special thanks to Betzi who made the original mesh for the crane
and to Miura who helped with the engine and weight settings,
also to Aperion for the slidenodes patch.
No mods of this without permission by me,
also no use of parts of this truck on other trucks without permission.
Skin mods don't need special permission, but don't upload the whole truck again
but only the edited texture files.
third upload to the repository another skin for my company rormart this skin is for the MAN TGX 26.530 with Palfinger PK 44002 that lenni made to install it you just put the DDS file in to your Lenni-MAN-TGX26530Crane-7a6eUID.zip and you done!
This is a mod of the International4700_pack. The trucks are all 1998 International 4700s and are as follows:
5th Wheel (DT466E)
Long Flatbed (T444E)
Terrain Truck (DT466E)
Sounds were recorded from a 1998 International 3800 school bus (built from the 4700) with a 7.6L DT466E, and from a T444E engine
Credits go to dneufeld for the original International 4700 pack