Browsing tag Trailers, found 189 matching files. (38 pages)
(updated on 14/8/12)
Im going to make this simple. Its Called LowPro. Simply stands for low profile.
Raise/Lower----CRTL + F1 / F2
Sliding Rear Axle----CRTL + F3 / F4
Ajustable Ride Hight
Dule Axle Gooseneck
Tri Axle Gooseneck
Fixed 81Ton Load - Gooseneck
Ravidnas1 - All
Support - Lots, Mainly ITOWU
Flares - DJ|Jasper - Thank you so much!!!
Disscuse - Here!
22 Comments, add comments here.
Liebherr 13HM mobile fast-erecting crane
All content is for use in Rigs of Rods only!
Use RoR 0.38.67+ for this!
- Detailed meshes
- Accurate kinematics
- Realistic lifting capacity (refer to the board on the crane!)
Start the engine and put the Crane in NEUTRAL!
- F1/F2: Rotate
- F3/F4: Trolley (use throttle to speed up if needed)
- F5/F6: Hook Up/Down (use throttle to speed up if needed)
- F7/F8: Extend/Retract Jib
- F9/F10: Raised-jib working angle
- Ctrl+F1/F2: Assemble/Disassemble
- Ctrl+F3/F4: Outriggers
- Ctrl+F5/F6: Legs
- Ctrl+F7/F8: Trailer wheel up/down
- Ctrl+F9/F10: Turn trailer wheel
- And as usual lock loads with "o"
You can also see the commands by pressing "T" ingame.
Basical procedure: Ctrl+F4 to fold outriggers; Ctrl+F6 once for legs, Ctrl+1 [NOT F1!] to display the baseplates, Ctrl+F6 again for legs. Then Ctrl+F2 to erect the crane automatically. Jib control is on F7/F8. Jib angle is on F9/F10. Retract automatically on Ctrl+F1.
- sputnik_1: meshes, node and beam, sounds, textures
- BigBoy, Craneman, Lifter, Inviteds, Donators: testing and help, thanks a lot!
15 Comments, add comments here.
(updated on 31/3/13)
Map: La Paz.
This pack is my attempt to capture the Streamline Moderne style popular in the 1930s and 1940s. The vehicles are all fictional, but their performance is realistic. I hope you'll enjoy driving them as much as I have enjoyed making them.
1948 Martin T64S "Custom" Tractor
A very low-slung 6x4 tractor. It has independent front suspension with double wishbones and load sharing rear suspension. The engine is a naturally aspirated 12-cylinder diesel driving through a 7-speed gearbox and locking differentials. Overall length is 29 ft, wheelbase 22 ft from front axle to centre of rear axle group, width 102 in, height 14 ft 9 in to tip of smokestacks. Kerb weight is 20,000 lbs, gross combination weight 80,000 lbs.
Fully loaded, the T64S will reach a top speed of 60 MPH with one of the included trailers. It will accelerate from 0-50 MPH in 1 minute, 0-60 MPH taking approximately 2 minutes.
1948 Martin O40 Tanker
A streamlined tank trailer in fictional "Hexaco" livery. Steel unibody, load sharing suspension. Overall length is 40 ft, wheelbase 28 ft from kingpin to axle group centre, width 102 in, height 10 ft 6 in. Loaded weight is 60,000 lbs.
1948 Martin F45 Flatbed
A simple flatbed trailer with stainless steel load deck and load sharing suspension. The deck is submeshed with the rollon flag and has ties to secure loads. Overall length is 45 ft, wheelbase 36 ft from kingpin to axle group centre, width 102 in, deck height 59 in, overall height 79 in to top of bulkhead. Kerb weight is 12,500 lbs, rated load 47,500 lbs.
1948 Martin V59 "Streamliner" Dry Van
A very large and somewhat impractical dry van. It has a streamlined stainless steel unibody and load sharing suspension. Overall length is 59 ft, wheelbase 47 ft from kingpin to axle group centre, width 102 in, height 14 ft 9 in. Loaded weight is 60,000 lbs.
These have only been tested in Rigs of Rods version 0.38.67.
The wheels have 40 nodes each, and the meshes were made in Sketchup. Don't expect these to be FPS-friendly.
The trailers are roll coupled via the system used by Lenni and Badboy for trailer steering. The centre of gravity and suspension are tuned accordingly; the trailers may topple easily on trucks that lack these nodes.
To minimise rolling resistance, the wheels are pushing the limits of the beam engine. They tend to oscillate when stationary. Caution is advised when stopping or parking on slopes as they may creep.
The trailers have very low drag. The T64S will not pull most other trailers at high speed.
CGTextures (restrictions apply, see below)
CGTextures does not allow redistribution of its textures under open source licences. You must remove/replace their texture before releasing modifications of this truck. All other assets used are available for modding. See the readme for specific file information and licensing details.
|Average Rating:||Tags:||HighQuality, Tanker, Flatbed, Box body, Trailers, 6x4, Semi, Transportation, Heavy Machinery, Land Vehicles||
Downloads today: 6, all time: 8337
19 Comments, add comments here.
(updated on 1/10/11)
Ekeri semi and rigid trailers for 6x2 Scania R560's
Openable rear and side doors
Fully contactible submesh
Korppi (Kuru): All meshes and N/B, some textures, basic skin
Salonen: better skin, ideas
Nexmartin: Refridgerator texture
Have fun =)
Rigid verson added 11/1/11
Remember to remove all previous versions, and regen cache.
|second upload to the repository another skin for my company rormart this skin is for the Ekeri trailer for 6x2 Scania R560 that kuru made to install it you just put the DDS file in to your ekeri.zip and you done!|
link to rormart: rormart
|(4 more mods here)|
22 Comments, add comments here.
(updated on 1/9/12)
This is the Mercedes Benz Actros 8x8 pack.
This package includes 8 versions:
- version with no upper part
- cartransporter (+trailer)
- log truck (+trailer NEW!)
- box-truck(+trailer NEW!)
- flatbed (+trailer NEW!)
It is version 1.1b in english.
Click here for discusing!
Please ask before publishing modifications, except skinzip-skins!
Special thanks to
|This is a ADAC (Algemeiner Deutscher Auto Club ~ German automobile club) - skin for the Actros 8x8 (Cartransporter (+trailer) ; box-truck (+trailer)).|
It works with the english and the german pack! v1.1b needed!
13 Comments, add comments here.