|
|
Browsing tag Tower Cranes, found 19 matching files. (2 pages)
Download all 19 files: Tower Cranes.zip (about 32.48 MB)
|
|
|
Liebherr 13HM mobile fast-erecting crane
All content is for use in Rigs of Rods only!
Use RoR 0.38.67+ for this!
Features
- Detailed meshes
- Accurate kinematics
- Realistic lifting capacity (refer to the board on the crane!)
Instructions
Start the engine and put the Crane in NEUTRAL!
- F1/F2: Rotate
- F3/F4: Trolley (use throttle to speed up if needed)
- F5/F6: Hook Up/Down (use throttle to speed up if needed)
- F7/F8: Extend/Retract Jib
- F9/F10: Raised-jib working angle
- Ctrl+F1/F2: Assemble/Disassemble
- Ctrl+F3/F4: Outriggers
- Ctrl+F5/F6: Legs
- Ctrl+F7/F8: Trailer wheel up/down
- Ctrl+F9/F10: Turn trailer wheel
- And as usual lock loads with "o"
You can also see the commands by pressing "T" ingame.
Basical procedure: Ctrl+F4 to fold outriggers; Ctrl+F6 once for legs, Ctrl+1 [NOT F1!] to display the baseplates, Ctrl+F6 again for legs. Then Ctrl+F2 to erect the crane automatically. Jib control is on F7/F8. Jib angle is on F9/F10. Retract automatically on Ctrl+F1.
Credits:
- sputnik_1: meshes, node and beam, sounds, textures
- BigBoy, Craneman, Lifter, Inviteds, Donators: testing and help, thanks a lot!
Support Thread |
| |
|
|
 15 Comments, add comments here.
|
|
|
Here is my Hyster top spreader i made for the vast amount of growing containers RoR has acquired.
Thanks to my beta testers for feedback.
once spawned the hyster will bounce a little just press backspace and it will be fine.
to hook onto a container slowly drive to the center of the container and extend the spreader(the spreaders extends more than the container so you do not have to be dead center to hook onto the container properly)
Make sure all 4 ties are secured and lift with the engine reved.
There is a readme with the controls.
any problems report to here. Hyster-reach-stacker |
| |
|
|
|
7 Comments, add comments here.
|
|
|
Felbermayr Skin for the Spierings Crawler Crane from craneman
to install
1. Put file into packs folder
2. have fun!
by the way - the color for the elevator comes with the new update from craneman  |
| |
|
|
|
No Comments yet. Add some here.
|
|
|
TREFFLER Skin for the Spierings Crawler Crane from craneman
to install
1. Put file into packs folder
2. have fun!
by the way - the color for the elevator comes with the new update from craneman
|
| |
|
|
|
No Comments yet. Add some here.
|
(updated on 25/9/11)
|
Hi,
this is my New Load - is a 280 To Press Part-
You need to lift the press at least two cranes of 500 tons Class
I've created the press in SketchUp, and Craneman has the n / b work done. my ROR Editor not works 
Thanks craneman for the good work!  |
| |
| Average Rating: |   | Tags: | Terex, Demag, Liebherr, Other Loads, Loads, Other Cranes, Mobile Cranes, Tower Cranes, Cranes, Heavy Machinery |
Downloads today: 1, all time: 4866 |
|
|
6 Comments, add comments here.
|
|
|
300 To Kolonne Load
N/B by Jo_Vink - Thanks for your Work!
you need at least 2xac500 , or the new comming soon crawler crane |
| |
|
|
|
4 Comments, add comments here.
|
|
|
skin van een staalbedrijf !
bestanden uit de zip halen en in de map van de sennebogen zetten en vervangen !!
groet liebherr mk100 |
| |
|
|
|
One Comment, add comments here.
|
(updated on 3/9/11)
|
Update 1.2
Hookcamera added!
notice: camera will only work on the original orange skin and not on the skinzip versions!
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
This is my Spierings crawler crane with 60m jib. It is able to lift 2t at the end of the jib! It is possible to give the jib an angle, And the elevator on the side of the tower can move up and down. It is also possible to edit the side panels for skinning and the main color can be changed.
Notice: First shift to the Reverse gear and then back to Neutral!
Controls:
F1/ F2: Rotate superstructure
F3/F4: Move trolley
F5/F6: Hook up/down
F7/F8: Jib angle
F9/F10: Move left track
F11/F12: Move right track
Ctrl+F1/F2: Elevator up/down
Don't complain in the thread about that it doesn't move or something because then you didn't read the description!
Credits:
Lenni: Helped me a lot with the n/b tracks! (thank you for that)
Bcazbobby: Helped me with fixing some bugs.
Thread for discussion or bug report:
http://www.rigsofrods.com/threads/71...-Crawler-Crane
http://www.youtube.com/watch?v=OXz8OWYHSj0
|
| |
|
|
|
|
10 Comments, add comments here.
|
|
Liebherr13HM.zip
view details
Gold
Silver
Bronze
