Browsing tag Heavy Machinery, found 15 matching files. (3 pages)
info: this is an mrt version of the manitou telehandler
4 stage extend-able boom
f3-f4: raise/lower boom
f5-f6: coupler curl in/out
f7-f8: extend/retract boom sections
f9-f10: attachment commands
f11-f12: center stabilizer (only use if on stable flat ground!)
ctrl-f1-f8: raise/lower stabilizers ( each stabilizer is independant so you can stablise yourself on uneven ground)
ctrl-f9-f12: extend/retract stabilizers
this machine was made to work with the attachments made for the manitou 731
to attach to an attachment just drive up to it slowly as it is set to auto-lock!
weighs roughly 16 tons
i haver permission from voulk to use his meshes
nodes and beams
rest of the meshes
7 Comments, add comments here.
f1-f2 boom up down
f3-f4 curl out/in
bucket grapple controls
f5-f6 open close
The machine is set to auto lock so you just need to drive up to the attachment.
5 Comments, add comments here.
This is the dumper-version of my Mercedes Kurzhauber. Everything is made by me. Its ropable, so you could also carry it.
Its a bad frameeater, but you can deactivate the mirrors and the mesh-wheels if you ve poor framerates.
Its not already done, but for the moment its some nice stuff i think.
you can connect trailers to the front- and the back-hook
You can lower and lift the supports with F1/F2
You can lower and lift the Dumper with F3/F4
You find find the WIP-Thread for my Mercedes trucks here:
As long as you give me credits, you re allowed do verything you like to and that makes the trucks better.
Using parts of my trucks for your own project surely also allowed, only let the people know who has done the originals.
It was nice to get an PM if you plan to publish it on other sites than these.
4 Comments, add comments here.
(updated on 31/3/13)
Map: La Paz.
This pack is my attempt to capture the Streamline Moderne style popular in the 1930s and 1940s. The vehicles are all fictional, but their performance is realistic. I hope you'll enjoy driving them as much as I have enjoyed making them.
1948 Martin T64S "Custom" Tractor
A very low-slung 6x4 tractor. It has independent front suspension with double wishbones and load sharing rear suspension. The engine is a naturally aspirated 12-cylinder diesel driving through a 7-speed gearbox and locking differentials. Overall length is 29 ft, wheelbase 22 ft from front axle to centre of rear axle group, width 102 in, height 14 ft 9 in to tip of smokestacks. Kerb weight is 20,000 lbs, gross combination weight 80,000 lbs.
Fully loaded, the T64S will reach a top speed of 60 MPH with one of the included trailers. It will accelerate from 0-50 MPH in 1 minute, 0-60 MPH taking approximately 2 minutes.
1948 Martin O40 Tanker
A streamlined tank trailer in fictional "Hexaco" livery. Steel unibody, load sharing suspension. Overall length is 40 ft, wheelbase 28 ft from kingpin to axle group centre, width 102 in, height 10 ft 6 in. Loaded weight is 60,000 lbs.
1948 Martin F45 Flatbed
A simple flatbed trailer with stainless steel load deck and load sharing suspension. The deck is submeshed with the rollon flag and has ties to secure loads. Overall length is 45 ft, wheelbase 36 ft from kingpin to axle group centre, width 102 in, deck height 59 in, overall height 79 in to top of bulkhead. Kerb weight is 12,500 lbs, rated load 47,500 lbs.
1948 Martin V59 "Streamliner" Dry Van
A very large and somewhat impractical dry van. It has a streamlined stainless steel unibody and load sharing suspension. Overall length is 59 ft, wheelbase 47 ft from kingpin to axle group centre, width 102 in, height 14 ft 9 in. Loaded weight is 60,000 lbs.
These have only been tested in Rigs of Rods version 0.38.67.
The wheels have 40 nodes each, and the meshes were made in Sketchup. Don't expect these to be FPS-friendly.
The trailers are roll coupled via the system used by Lenni and Badboy for trailer steering. The centre of gravity and suspension are tuned accordingly; the trailers may topple easily on trucks that lack these nodes.
To minimise rolling resistance, the wheels are pushing the limits of the beam engine. They tend to oscillate when stationary. Caution is advised when stopping or parking on slopes as they may creep.
The trailers have very low drag. The T64S will not pull most other trailers at high speed.
CGTextures (restrictions apply, see below)
CGTextures does not allow redistribution of its textures under open source licences. You must remove/replace their texture before releasing modifications of this truck. All other assets used are available for modding. See the readme for specific file information and licensing details.
|Average Rating:||Tags:||HighQuality, Tanker, Flatbed, Box body, Trailers, 6x4, Semi, Transportation, Heavy Machinery, Land Vehicles||
Downloads today: 11, all time: 9307
20 Comments, add comments here.