How to lift off, fly and pick up a load...READ THIS FIRST
- you can always see a help-chart by pressing and holding F4 in pilots view ( SAR and Logger only )
- you can get a better overview by pressing F3 once in pilots view, released by pressing F4 once ( SAR and Logger only )
Enter the helicopter
Press the Parking Break
ctrl (strg) Pos1: Fire up all engines simultaneously
ctrl (strg) Page up: Maximum Power to all engines
Page down once, you overpower it and please reduce it by 1 click, only use the BOOST for extrem Load lifting, it will stress the rotorheads to the absolute maximum they can withstand. If the AOA-Inidicators is permanently OVER 15 ( the red marker ), you need a parachute
..wait until engines reach green area... 96 RPM (%)
gently apply F1 until the Helicopteri lifts off
Arrowkey UP: Accelerate/forward flight: Nose down ..watch your height and apply more lift if needed (F1)
Arrowkey Down: Breaking/reverse flight: Nose up, reduce lift for some time not to gain too much height (F2)
Z/X (Y/X) :Turning, will do a pivot in hover mode that needs minor corrections not to drift / accelerate...just watch the virtual horizon Will bank and turn in forward flight faster then 30 knots, additional nose down + banking = higher turn ratio..
Arrowkeys Left/Right: Strafing while hovering, Bankingl left/right in forward flight
HOW TO:
1. Picking up a load
Land close to a load with ONE ropable, best placed in top center
Press O to shoot out the tie
Wait for the tie to move the hook sideways
Apply rope to let the tie pull the node to the ropable at the load (F5)
When tie stops working, lock the hooknode (L) and then release the tie (O)
Apply more rope to get some manouver space for the heli
-> Start, center the heli over the load, climb slowly, correct against the weight of the load and lift it off (F1)
- Pull the load close to the heli with F6 to fly and gain control
Releasing it is easy: L to drop it, F6 and then L to place it
You can lift and fly 13 tons, dont go too fast or the rotorhead will deform permanently and you need a parachute instantly
2. Rollon Loads: (SAR and Logger only)
Drive in a car with 5 (!) ropables, one on each edge and one in the center.
Park in the middle of the Helicopter, activate Parkingbrake, switch of the engine, leave the car
Enter the helicopter, Press "O" to tie the car down. It needs to be really centered in the helicopter, weight balancing is vital for flight characteristics.
This RoR's first single rotor helicopter with collective and cyclic flex rotor head and static rear rotor transmission that flies stable and very controllable.
Approximately 9 months of development.
No mods without permission!
Credits:
DeGa
Lifter
Have fun.
How to fly:
All engines at full power ( Ctrl-Home and then Ctrl-PageUP ) and Rotor-head RPM Indicator GREEN ( Cockpit view, top left indicator) to fly.
Check the T-Screen for commands, its all in there.
Special features:
- featuring an automatic hover aid system, its very easy to control while flying slow trying to hover in position and at height.
- hook with extended grip range...to make load pickups easier, the hook in the middle has a hook-range upgrade.
A rotary wing prototype I worked on for a while and recently decided to upload. It's designed to mimic the way modern helicopters work and is thus just like real helicopters capable of flying upside down. It flies quite stable and with a little practice is easy to use.
Controls:
Up/Down arrows controll ascent/decent
Left/Right arrows rolls the craft to the left and right
Z/X rotates the craft
F2 pitches forward F1 pitches backwards.
Flaps can be used to create a constant positive lift when you want to concentrate on manouvering.
Start both engines and set them to full throttle before waiting for about fifteen seconds for both rotors to spin up to full speed. Then use the up arrows to take off and the other controlls to keep the craft steady. With practice the helicopter is quite responsive and manouverable.
Left/Right to steer
F1 to make the front go up,
F2 for it to go down.
The most left throttle control is for the top rotor. The other 3 are for the other one.
the keys fo get off are f1 up und f2 down
for carlift use f3 and f4
f5 and f6 is in use for gear up down
f7 and f8 for gear suspention
f9 and f10 load bay
LilBunniFuFus helicopter modded by myself to have skids, this time with a fixed menu name, the last time it had the same name as LilBunniFuFus version, now it has a different one, I hope your landings are easier, and have fun!
Boeing-CH47-Chinook.zip
view details
(beta version)
Gold
Silver
Bronze
