Trailer P-32 is designed for quick transport wheeled and tracked vehicles and other material to the weight of 40 tons. In an emergency, up to 46 tons, maximum speed may be 10 km / h Is designed for off-set with tractor on roads I to III. class, the roads are paved and after tolerable terrain without external imbalances and obstacles.
Technical and tactical data
Dimensions:
- Total length (including shaft): 9475 mm
- Overall height: 1420 mm
- Height of the loading area: 1000 mm
- Overall width: 3100 mm
- Wheelbase: 4410 mm + 1000 mm
Loading area:
- Length: 4900 mm
- Width: 3100 mm
weights:
- Standby: 10,600 kg
- Payload: 40,000 kg
All content is for use in Rigs of Rods only. Read the copyright file included in the zip!
This is a small map I built for my erectable wind engine.
Features:
- Contains all parts of my fully transportable and erectable wind engine. See included manual for button assignments
- A winding road to transport the windmill pieces
- A small train track with tunnels
- Nice looking textures and vegetation (Thanks for all your help DeGa!)
I will not make a FPS version of this! If your PC can't handle it, buy a new one.
Credits:
- sputnik_1: meshes, node and beam, textures, map
- DeGa: massive help on the terrain, thank you so much
- BigBoy, Craneman, Inviteds, Donators: testing and help, thanks a lot!
A pack of flatcars (standart 40ft, bulkhead 40ft and heavy weight 8-axle), all come with different skins.
The couplers can be locked/unlocked (both sides like on my ALP!) with the bigger lever at one end, on the other end there is a lever for the handbrake. Grab those with the mouse, you do not need to enter the waggons
Known bugs:
If you enter a flatcar through the vehicle selection menu game will crash if you try to exit the flatcar, simply change into another enterable vehicle via the menu and exit there.
Thanks to:
sputnik_1 for helping me with adjusting the node/beam.
Here is a skin for the Kenworth T600 and a 2 axle tanker trailer. The skin is based off of fuel delivery trucks for HESS gas stations. I made the skin as close to the actual paint job as possible.
Credits:
Kenworth T600 - HemiBoy95 & Box5Diesel
Tanker Trailer - Trevor
Inspiration - My father
Skins - Venem (me)
Here is the first US rolling stock, so you can finally tow some waggons with my ALP.
A loadable 40ft boxcar, comes in several liveries.
You can open the doors by grabbing the levers at the doors, the couplers can be locked/unlocked (both sides like on my ALP!) with the bigger lever at one end, on the other end there is a lever for the handbrake. Grab those with the mouse, you do not need to enter the waggons
Known bugs:
If you enter a boxcar through the vehicle selection menu game will crash if you try to exit the boxcar, simply change into another enterable vehicle via the menu and exit there.
Thanks to:
donoteat, maddrix for skins
sputnik_1 for helping me with adjusting the node/beam.
*BUG FIX* LATEST UPDATE
I'd like to say I've fixed the "Big Tex Goseneck.load"
*ever sense .38's "Pinguinville" came out there have been various conflicts with the map's and it's own materials & meshes, merely the extent to which I altered the trailer is merely changing the mesh names to void such conflicts*
*-all credit belongs to the original authors!!! I only modified material names!!
"Fixed" list:
*wheels
*spawning errors on Pinguinville & Minima
*wheel-face bug
*suspension is on the wheels,where it should be, not on the ramps
*the jacks raise and lower a little funny, but they work
*also added two axel version with (slightly) less moving when parked, and backing-up bug is fixed
the sliding-around-while-parked bug is still unsolved...if you have suggestions (or soulutions ^.^) to fix it plz let me know(PM me)
if any other problems protists feel free to pm, but remember i just fixed some bugs, skinning and stuff is tangycrose 's domain
All credit is held by:
tangycrose & Box5
This is a mod to box5's goose neck. I made it shorter and made it have two axles. The mod was simply to make it look better when hauling stuff around. In my opinion the normal one is a little large.
Original trailer is box5s
Mod by me
And i know the mod isn't perfect. May over write the old one.
Original file http://www.rigsofrods.com/repository/view/585#comments
This is a mobile home or mobile office depends on how you use it. You can pull it to your location and pull the tires into the body and it will be on the ground like a house. It is a decent amount of weight 22046.23lbs. It is fun to pull around comments are greatly welcomed. This is a 10x40 trailer its not a CAMPER.
made by me
Update 1. made the tongue longer fixed the tires problems added more weight
I was searching the forums recently, and discovered that there were no ramps to jump cars off of, so I decided to create one. This is a car-sized "Kicker" ramp based off of those that are used for skateboarding. It has a tow hitch so you can drag it around with trucks, so moving it is possible. It only weights 150 Kg, so most vehicles can tow it. As a side note, this is my very first mod for any game.
+Add more types of ramps, especially tilted ramps and sliced quarter pipe ramps.
Change Log:
V3:
+ Added New Twisted Ramp 'RoR Ramp "Twisted Kicker" - Plastic'
+ Added New Twisted Ramp 'RoR Ramp "Twisted Kicker" - Full Metal'
V2:
+ Renamed Original Ramp to 'RoR Ramp "Kicker" - Plastic'
+ Added New All Metal Ramp: 'RoR Ramp "Kicker" - Full Metal'
+ Full Metal ramp weighs more than Plastic ramp.
+ Plastic ramp is still compatible with people that still have V1
+ Fixed some errors.
[Moved Props section below nodes]
V1:
+Initial Release
Everything was created by me.
To Modders of Mods:
I know who I personally have given permission to mod this, so don't mod without permission.
Link to Discussion: RoR-Ramp (More Frequent Updates)
IMPORTANT!
Heavy vehicles or vehicles with large tires risk causing the ramps to slide. The ramps were designed for lighter vehicles and are physically designed to be light so they can be towed by normal vehicles such as SUVs or Pickup Trucks (Including the S10).
This is a MB Car Rental skin for Wabash Duraplate trailer.
NOTE: unzip and put all the files but the read me in the WabashDuraplate.zip
Authors: Nadeox1 (trailer), Mitchieboy (MitCity's MB Car Rental)
link for Nadeox1's Wabash Duraplate: 53-Wabash-Duraplate
link for MitCity by Mitchieboy: http://www.rigsofrods.com/repository/view/4904
This is a Trollstore skin for Wabash Duraplate trailer.
NOTE: unzip and put all the files but the read me in the WabashDuraplate.zip
Authors: Nadeox1 (trailer), Mitchieboy (MitCity'sTrollstorel)
link for Nadeox1's Wabash Duraplate: 53-Wabash-Duraplate
link for MitCity by Mitchieboy: http://www.rigsofrods.com/repository/view/4904
This my Goldhofer STNL3-Platform trailer "Speedy".
"Speedy" is a very flexible and light platform trailer.
Commands:
CTRL+ALT+F1/+F2: lower/raise trailer legs
CTRL+ALT+F3/+F4: lock/unlock steering (lock for reverse driving or extending trailer/steering is locked when trailer spawnes)
CTRL+ALT+F5/+F6: extend trailer
CTRL+ALT+F7/+F8: raise/lower liftaxle
CTRL+ALT+F9/+F10: raise/lower trailer ramps
Note: All commads exept ramps are one-press-commands.
Hope you like it :-)
This is a pack of wooden crates. I have attempted to make them sort of high-detail and I think I have succeeded for the most part. There are many variations inside, so look at the list below. In the future I am willing to make more requests for different versions. These crates have a 'hooking point' for cranes and also have 'ropables' so you can fasten them to other vehicles. They also include a submesh so they can be contactive with other submeshes/contactive structures. They emit really good framerate because of the simply-low node/beam count. They can be used in groups without affecting your framerate heavily. There are many versions, too.
Normal (OSB)
IKEA
THW
UN (UNHCR)
U.S. Army
TNT Crate
Radioactive biohazard
DHL Express
Soviet Crate
CREDITS
Beolex - 3D Modeling/nodes & beams/texturing
Venem - Assisting with beam color
Pull the trailer next to the load so the rear part is at the right place.
Disconnect the rear part with F11 and pull the front part to the front attachment point.
Use a crane to put the load on, the wood load also has invisible legs so it can be loaded without crane, use F9/10.
The steering strength can be adjusted with F5/6 to fit to the length of the load.
The rear part has manual steering for special situations: F7/8, don't use when the steering is already at maximum angle!
The legs fold in automatically if you pull them up with F1, hold F2 until they fully fold out.
The load will attach on the trailer automatically once it is close enough to the right position.
To unload push F12, but attach it to a crane first and put enough tension until the trailer almost lifts off!
Thanks to Lifter for the hookgroups and triggers and for support with this project!
Thanks to fidoj for his roof part load!
Please do not modify this without my permission,
skins can be added using the skin file system: skins-working
If this system is used properly then no need for my permission for skins.
This Is A Mod Of Truckian Arrow Board Trailer I Added Wheels To It So You Can Have It In 38.67 Not Sure About Above Or Below Cause I Only Have It For 38.67 Try It Your Self And Let Me Know
CREDITS
Truckian The Orginal Owner
mitcitylover Added wheels
PM me if you have any problems and DO NOT SPAM the comment box thank you.
It can load 1x 40', 45' or 48' are also possible, but that may result in too much front and rear overhang and then the container might hit the tractor unit.
The other possibilities are 2x 20', 1x 20' in the middle or at the end with retracted chassis back.
You can extend and retract the rear end to fit different containers on, and it is possible to adapt the suspension to different heights and loads,
the command keys show up in the ingame preview.
There is also a version with two containers fixed to the trailer for people who don't bother loading or unloading it.
If you want to reskin it please use the GUID system and skinzip files, then you can upload your skins to the repo.
Don't modify anything else or use parts of it on other models without my permission please.
this is my modification to Box5diesel's sledpull
I added an engine an other skin and a beacon
credits: Box5diesel for the original sledpull
and me ( jerom ) for the modification's
second upload to the repository another skin for my company rormart this skin is for the Ekeri trailer for 6x2 Scania R560 that kuru made to install it you just put the DDS file in to your ekeri.zip and you done!
Here's a trailer I made awhile back with a detaching Neck. It can haul some big stuff, has a flexbody deck that bends flat with a heavy load and flexes over bumps. Its not all that finished, but its as finished as its gonna get, lol. I made a video to show how to use it
Ctrl F1 to raise the neck so you can back under and lock on
Ctrl F2 seats the neck on the hitch after you locked on
Ctrl F3 attaches neck to the trailer
Ctrl F4 detaches neck so you can drive it out of the way to load/unload
In a game where approximately 99.9% of the players like to see things get destroyed, mauled, smashed, torn to shreds, incinerated, devastated, set on fire, and blown up, a load like this is more than necessary. Oxsergy and I (Beolex) bring you the Destructible Barricade. This is a meshed load which makes a good backdrop as scenery to your terrain, or just eye-candy for you masochistic freaks that like seeing things get destroyed. It is a tri-section load, meaning it has two legs and a board that can all rip apart for your disastrous pleasures. It is recommended that you pre-place it on a terrain so it is permanently there whenever you run the game, but it is also lift-able (via crane/boom) and can be placed in the bed of a vehicle and secured, too. However, to keep this barricade realistic, it needed to be semi-weak so it can be destroyed by most moving forces. As a result, hauling/lifting this with machinery can result in the barricade breaking, as it is fragile.
CREDITS
Beolex - Mesh creation and texture work
0xsergy - N/B structure and refinement/finalization
Ackermann Moving Trailers
Here are my moving trailers for both the Buessing and the Mercedes Moving Vans.
They have managed materials and material-flares, and are useing sections.
They're not loadable... just some nice trailers to pull around.
Today, me and Brickman bring you a generator load, the RORGEN GX70000. It is simply a mesh placed on a n/b chassis.
Features:
-Engine, for realism.
-Ropables, so you can pick it up with a crane.
-Contactable, so you can place it in a truck bed or on a trailer.
-Exhaust, for realism.
-Full-Mesh
-It also features a large wheel on the inside (viewable by pressing the "K" key), which spins faster as the engine RPM increases .
We are hoping to release updates and/or new models under the RORGEN name, so stay tuned!
Credits:
Me (ROR-EMS): Mesh, idea
Brickman: All N/B work, Engine, Mesh help.
Feedback is always welcome!
Note: If you want to use the n/b, mesh, or any components of this project in a mod of your own, please request permission from me first, and I will either grant/decline you permission for the parts of this project I am responsible for, or I will forward you to Brickman, for the parts he is responsible for.
This is a simple small bumper pull camper. It is my second camper i have made. This one is a little unsteady when going over 60. And the one with extra weight on the tires sways sometimes. I will continue to fix these problems though. The normal non weighted one does roll sometimes.
This is a MB Equipment skin for Wabash Duraplate trailer.
NOTE: unzip and put all the files but the read me in the WabashDuraplate.zip
Authors: Nadeox1 (trailer), Mitchieboy (MitCity's MB Equipment)
link for Nadeox1's Wabash Duraplate: 53-Wabash-Duraplate
link for MitCity by Mitchieboy: http://www.rigsofrods.com/repository/view/4904
This is my first upload. I made ?pallet of gold for you. They are four variants ( 1095 kg,1976 kg, 2912 kg, 3432 kg). Sorry for my bad english. Enjoy it
Autor: Pedro
Vojta1991
This is a skibox which can be attached to both tourliner versions.
The README.pdf is included in the zip.
Please post any problems and discuss here: NEOPLAN-tourliner
Unfortunately I made a silly mistake, so RoR displays ;V 1.0 in the select menu instead of the name of the box... You can cin a fix for that in the fist post of the thread you find above.
second upload to the repository another skin for my company rormart this skin is for the Ekeri trailer for 6x2 Scania R560 that kuru made to install it you just put the DDS file in to your ekeri.zip and you done!
Transportable traffic lights for construction sceneries.
The pack contains two traffic lights, spawn one of each of them to have correctly alternating red and green lights.
They are transportable and can be lifted with cranes.
version 5, 4x4 trailer & jeep trailer
there is an invisible leg to lift the front to lift it
press+hold F2, hit ' L',once its attached press F1 for a few seconds to retract the leg.
Hello, I'm happy to introduce my first ever official mod to a trailer, It is a monster energy skin for the FEDEX 53ft Great Dane dryvan, Just throw it in packs, Because of the (1) at the end it will not overwrite, So enjoy, I hope it is a cool mod to you guys, It took about 3 hours to get it right... haha.
Set of ISO shipping containers. Contains 20', 40', 45', 48', and 53' sizes.
Many thanks to fidoj and sputnik_1 for the chassis and locking mechanism.
Many many thanks to the community for submitting so many skins for these things! In the mods section below, you'll find eight skinzips full of 150 skins produced by the RoR community. (And almost all of them are tolerably good!)
Total 5 loads you can have fun whit including a fire flatbed that is high detailed whit working watargun!
All the container with doors or ramps:
Open/Down:F8
Close/Up:F7
The fire container:
Turn water hose:F1-F2
Down and up water hose:F3-F4
Note that need to seat inside the fireflatbed to start engines and control watergun!
This is a modular house often used on constructions site or as a modular office. It is a simpel mod of the 20ft container by LostSoul3471. I added 4 more hock nodes, this will not efect how the container forklifts handles it, but make it easier to lift it with cranes. I also made it lighter than the original container. you can stack them on each other. It is fully independent and will not overwrite the original containers. It is still a beta.
A telecopic trailer based on OVB-55-03V(T) model from Nooteboom.
features and commands:
- can extend up to 40m (CTRL+F1/F2)
- manual steering (F7/F8)
- adjutable suspension (CTRL+F3...F8)
- drop sides, to prevent falling loads (CTRL+F9/F10)
- fully working ligths
- avaible in 3 colors: red/yellow/blue
All commands are written on the front left side of the trailer
skstep.zip
view details
Gold
Silver
Bronze
