Features
- Detailed meshes
- Accurate kinematics
- Realistic lifting capacity (refer to the board on the crane!)
Instructions
Start the engine and put the Crane in NEUTRAL!
- F1/F2: Rotate
- F3/F4: Trolley (use throttle to speed up if needed)
- F5/F6: Hook Up/Down (use throttle to speed up if needed)
- F7/F8: Extend/Retract Jib
- F9/F10: Raised-jib working angle
- Ctrl+F1/F2: Assemble/Disassemble
- Ctrl+F3/F4: Outriggers
- Ctrl+F5/F6: Legs
- Ctrl+F7/F8: Trailer wheel up/down
- Ctrl+F9/F10: Turn trailer wheel
- And as usual lock loads with "o"
You can also see the commands by pressing "T" ingame.
Basical procedure: Ctrl+F4 to fold outriggers; Ctrl+F6 once for legs, Ctrl+1 [NOT F1!] to display the baseplates, Ctrl+F6 again for legs. Then Ctrl+F2 to erect the crane automatically. Jib control is on F7/F8. Jib angle is on F9/F10. Retract automatically on Ctrl+F1.
Credits:
- sputnik_1: meshes, node and beam, sounds, textures
- BigBoy, Craneman, Lifter, Inviteds, Donators: testing and help, thanks a lot!
Mesh of the uppercabin is made by Craneman
Other mesh parts are made by me
N/B axles are made by Craneman
what you get is:
Terex-Demag ac500 with ssl
Terex-Demag ac500 without ssl
Terex-Demag ac500 with 18m fixed jib
Terex-Demag ac500 with 30m fixed jib
Terex-Demag ac500 with 36m luffing jib
Terex-Demag ac500 with 60m luffing jib
Terex-Demag ac500 with 90m luffing jib
controls:
f1 or f2 = turn left or right
f3 or f4 = boom up/down
f5 or f6 = hook up/down
f7 or f8 = cab up/down
f9 or f10=counterweight systeem up/down press K too see it
f11 or f12=jib up/down
ctrl+f1 or ctrl+f2=boom1 in/out
ctrl+f3 or ctrl+f4=boom2 in/out
ctrl+f5 or ctrl+f6=boom3 in/out
ctrl+f7 or ctrl+f8=boom4 in/out
alt+f1 or alt+f2 = suspension up/down
alt+f5 or alt+f6 = outriggers turn
alt+f7 or alt+f8 = outriggers in/out
alt+f9 or alt+f10 = outriggers up/down
alt+f11 or alt+f12=cab turn
ctrl+alt+f1 or ctrl+alt+f2 = axle 5 lift
ctrl+alt+f3 or ctrl+alt+f4 = ssl up/down
ctrl+alt+f5 or ctrl+alt+f6 = ssl sidemoving
ctrl+alt+f7 or ctrl+alt+f8 = ssl ropes ssl till boomhead
ctrl+alt+f9 or ctrl+alt+f10 =couterweight boom up down only by versions needed with luffing jib
ctrl+alt+f11 or ctl+alt+f12=crab steer
i hope i have write all commands
look at the first post of ac500 topic for pictures how the counterweight systeem work (demag-ac500)
with 24,3m mainboom
with 35,5m mainboom
with 46,7m mainboom
with 57,9m mainboom
with 69,1m mainboom
with 24,3m mainboom and 24,3m jib
with 24,3m mainboom and 35,5m jib
with 24,3m mainboom and 46,7m jib
with 35,5m mainboom and 24,3m jib
with 35,5m mainboom and 35,5m jib
with 35,5m mainboom and 46,7m jib
with 46,7m mainboom and 47,7m jib
the commands are:
f1 and f2 for turn around
f3 and f4 for boom up/down
f5 and f6 for hook up/down
f7 and f8 for jib up_down
f9 and f10 for left track moving
f11 and f12 for right track moving
alt+f1 and f2 for cablift up/down
alt+f3 and f4 for cab up/down
credits or help:
lenni for helping with the tracks
cranedriver for some mesh parts
gamer18 for n/b and mesh
DS9 Off Shore Crane - Science Research & Salvage
Belongs to the DS9 Submarine!
It features:
- a 2-bridged overhead crane on the water
- sidewarts extendable main booms to unload onto the land
- a car/cargo deck that can lock down loads and cars.
- a car ramp to drive on/off with vehicles..
- hooks that go under water to pick up sunken ships or loads
- side-thrusters for better manuverability
- underwater flares to see what you lift at night..
it can lift/transport/unload at least 70 tons!
I haven't tried heavier stuff..
This Crane is opensource - do with it as you like..
Press "O" to use ties and hook in 4 points (needed if you want to rotate the load)
or
Presss "L" to hook in 1 point
Note: to enter the crane, you need to be placed under the cab; and if the crane is on the stabilizer, you'll need to jump to enter. the cab is a little high
O hook a load
LEGS
ctr+f1/f2 legs left unfold
ctr+f3/f4 legs right unfold
ctr+f5/f6 legs left in/ out
ctr+f7/f8 legs right in/out
ctr+f9/f10 legs up/down
alt+f5/f6 rear legs cylinders do not turning more (not important ,in real these cylinders are in most of time down.)
UPDATE
-front legs cylinders are stronger
-front tires are stronger
-use wheelmesh
-visuale bugs of hinge points fixed
-change what of color
-legs visual better
-added jib version
PALLETLIFTER
hook A pallet press ALT-f12 ,unhook the pallet press ALT-f11
For the first start the hook is on ,so you have nothing to do.
You can pickup the palletlifter with press h (this crane has an hook-node in the hook) or O just for other cranes.
LOADING BOX
Drive the truck under the box ,it will automatic hook the box .
Press CTR+ALT f1 for legs in .
For unhook the box press ALT+L
LEGS
alt+ f1/f2 legs left in/out
alt+ f3/f4 legs right in/out (use right alt ,left the game will close)
alt+ f5/f6 legs left in/down
alt+ f7/f8 legs right up/down
alt+ f9/10 leg front up/down
ctr+alt f1/f2 legs loadingbox up/down
BOOMS
ctr+ f1/f2 boom1 in/out
ctr+ f3/f4 boom2 in/out
ctr+ f5/f6 boom3 in/out
ctr+ f7/f8 boom4 in/out
ctr+ f9/f10 boom5 in/out
ctr+ f11/f12 boom6/7/8 in/out
f9/f10 jib booms in/out
f11/f12 manual jib booms in/out (works only when the hook is not loaded)
HOOK LOADS
L hook /unhook trailerhook or cranehook
alt+ F11/F12 unhook/hook palletlifter
Project TATRA 815 CKD AD-28 is finally COMPLETE.
You can download it and have fun with this crane.
COMMAND for use:
F1 - F2 : rotation crane tower
F3 - F4 : lift arm
F5 - F6 : disengagement arm
F7 - F8 : spooling hook
ctrl + F1 - ctrl + F4 : disengagement/clutch shelf
ctrl + F5 - ctrl + F12 : dusebgagement/clutch shelf (up/down)
Before you start drive you must locked hook nose oof cabin, because it will cradle. For locked use button "L" and locked arm button "O".
Liebherr13HM.zip
view details
Gold
Silver
Bronze
