This is a 1976 Ford W-9000 cab-over-engine semi tractor. A fairly basic node-beam vehicle that will get the job done. All of the pieces for this were created by me (M-138) except the mirrors. Feel free to modify, just remember to give credit.
This pack is my attempt to capture the Streamline Moderne style popular in the 1930s and 1940s. The vehicles are all fictional, but their performance is realistic. I hope you'll enjoy driving them as much as I have enjoyed making them.
1948 Martin T64S "Custom" Tractor
A very low-slung 6x4 tractor. It has independent front suspension with double wishbones and load sharing rear suspension. The engine is a naturally aspirated 12-cylinder diesel driving through a 7-speed gearbox and locking differentials. Overall length is 29 ft, wheelbase 22 ft from front axle to centre of rear axle group, width 102 in, height 14 ft 9 in to tip of smokestacks. Kerb weight is 20,000 lbs, gross combination weight 80,000 lbs.
Fully loaded, the T64S will reach a top speed of 60 MPH with one of the included trailers. It will accelerate from 0-50 MPH in 1 minute, 0-60 MPH taking approximately 2 minutes.
1948 Martin O40 Tanker
A streamlined tank trailer in fictional "Hexaco" livery. Steel unibody, load sharing suspension. Overall length is 40 ft, wheelbase 28 ft from kingpin to axle group centre, width 102 in, height 10 ft 6 in. Loaded weight is 60,000 lbs.
1948 Martin F45 Flatbed
A simple flatbed trailer with stainless steel load deck and load sharing suspension. The deck is submeshed with the rollon flag and has ties to secure loads. Overall length is 45 ft, wheelbase 36 ft from kingpin to axle group centre, width 102 in, deck height 59 in, overall height 79 in to top of bulkhead. Kerb weight is 12,500 lbs, rated load 47,500 lbs.
1948 Martin V59 "Streamliner" Dry Van
A very large and somewhat impractical dry van. It has a streamlined stainless steel unibody and load sharing suspension. Overall length is 59 ft, wheelbase 47 ft from kingpin to axle group centre, width 102 in, height 14 ft 9 in. Loaded weight is 60,000 lbs.
Notes
These have only been tested in Rigs of Rods version 0.38.67.
The wheels have 40 nodes each, and the meshes were made in Sketchup. Don't expect these to be FPS-friendly.
The trailers are roll coupled via the system used by Lenni and Badboy for trailer steering. The centre of gravity and suspension are tuned accordingly; the trailers may topple easily on trucks that lack these nodes.
To minimise rolling resistance, the wheels are pushing the limits of the beam engine. They tend to oscillate when stationary. Caution is advised when stopping or parking on slopes as they may creep.
The trailers have very low drag. The T64S will not pull most other trailers at high speed.
Licence
CGTextures does not allow redistribution of its textures under open source licences. You must remove/replace their texture before releasing modifications of this truck. All other assets used are available for modding. See the readme for specific file information and licensing details.
This is a mod of the International4700_pack. The trucks are all 1998 International 4700s and are as follows:
5th Wheel (DT466E)
Gooseneck (T444E)
Flatbed (DT466E)
Long Flatbed (T444E)
Terrain Truck (DT466E)
Sounds were recorded from a 1998 International 3800 school bus (built from the 4700) with a 7.6L DT466E, and from a T444E engine
Credits go to dneufeld for the original International 4700 pack
Some bugs still exist like the front axle bending when turning especially since it only has 1 front axle now.
Credits:
Kuru for the N/B, Engine, Tool boxes & Fuel tanks
Lenni for the wheels
HRVI for making them
Any questions or what ever PM me or ask on here: Scania-142-Heavy-Hauler-Tipper-(Beta-First-Final-public-release)
Do not release mods without asking me via PM first!
This is it after a few months: the Seridon Si14 from Seridon Motorhomes
This is my first creation from scratch, and it's a bit oversized. The next versions will be better scaled
In the next update it is colorable
Credits:
Me: n/b and mesh
haselnut116601: support, door n/b and loads of other stuff
rainingheavy: steeringwheel and placement
Scalefreak93: shocks
Nickster 7: wheels
bray: engine settings
I don't remember all the people who helped me, so report it to me if I forgot someone!
-updated version, rope spreading works now and ballastbox sides don't lock up anymore-
-new update: wheel definition updated and new working mirrors added.
This is a pack with a semi version and a ballastbox version of this truck,
it also contains a jib which can be fitted to both versions.
After a very long time of making this truck it is finally finished,
it features a fully funcional crane,
animated parts like driveshafts and control levers
animated cockpit, lights all around the truck,
custom sounds and a contactable surface on the truck.
Special thanks to Betzi who made the original mesh for the crane
and to Miura who helped with the engine and weight settings,
also to Aperion for the slidenodes patch.
No mods of this without permission by me,
also no use of parts of this truck on other trucks without permission.
Skin mods don't need special permission, but don't upload the whole truck again
but only the edited texture files.
Use with 0.37.126 or higher
*doesn't include the terrain and the pallet,
pallet is in this pack: 30t-mobile-non-slewing-crane
terrain here: 2506
third upload to the repository another skin for my company rormart this skin is for the MAN TGX 26.530 with Palfinger PK 44002 that lenni made to install it you just put the DDS file in to your Lenni-MAN-TGX26530Crane-7a6eUID.zip and you done!
UPDATE
added Traction control, slope brake and the sections parts back in so you can choose different colors within the menu when loading the truck.
UPDATE2
fixed the spelling mistake on the ropables so they all work now
UPDATE 3
fixed the material file error and added a few visual enhancements. made the axles and springs black and chromed the diff covers and driveshafts
Many months in the working it's finally here
Various modified version made by me. all the ones with more than 2 axles, the 3rd axle is liftable and the ones with more than 3 axles the 4th and 3rd axle are liftable.
on the heavy haul versions with 4 axles only the front axle is liftable.the heavy haul versions can haul 200tons, mainly the 3axle and 4axle versions.
Kenworth T800W tri-axle Daycab longframe
Kenworth T800 daycab short frame
Kenworth T800 daycab short frame Tbox
Kenworth T800 4th axle Extended Flatbed
Kenworth T800 boxtruck 4th axle
Kenworth T800W toolbox tri-axle Daycab longframe
Kenworth T800W sleeper tri-axle longframe heavy haul
Kenworth T800 tilt Flatbed long frame 4-axle
Kenworth T800 dumptruck 4th axle
Kenworth T800W sleeper two-axle longframe
Kenworth T800 2 axle Extended Flatbed
Kenworth T800 sleeper Extended Flatbed tri axle
Kenworth T800 sleeper short frame
Kenworth T800 sleeper short frame Tbox bed
Kenworth T800W sleeper toolbox tri-axle longframe
Kenworth T800 sleeper Flatbed short frame
Kenworth T800 sleeper short frame heavy haul
Kenworth T800 Long frame Logtruck
Kenworth T800 longer Tanker
Kenworth T800 Extended Flatbed tri-axle
Kenworth T800W two-axle Daycab longframe
Kenworth T800 Daycab 2 axle shorter frame
Kenworth T800 two axle boxtruck
Kenworth T800 dump truck 2 axle
Kenworth T800W Daycab heavy haul tri-axle shorterframe
Kenworth T800 tilt Flatbed long frame Tri-axle
Kenworth T800 Tilt Flatbed regular frame
Kenworth T800W sleeper heavy haul 4-axle heavyframe
Kenworth T800W Daycab heavy haul 4-axle heavyframe
Kenworth T800 tri axle boxtruck
Kenworth T800 Flatbed short frame
Kenworth T800 terrain editor
Commands for the Various trucks that have liftable objects.
All truck have opening hoods F3-F4
Kenworth T800W tri-axle Daycab longframe F7-F8 for lift axle
Kenworth T800 4th axle Extended Flatbed F9-F10 for lift axle
Kenworth T800 boxtruck 4th axle F5-F6 for lift axle
Kenworth T800W toolbox tri-axle Daycab longframe F7-F8 for lift axle
Kenworth T800W sleeper tri-axle longframe heavy haul F7-F8 for lift axle F9-F10 for movable fifth wheel
Kenworth T800 tilt Flatbed long frame 4-axle F-7-F-8 to lift axles F9-F10 to lift bed F-11-F-12 to open tailgate
Kenworth T800 dumptruck 4th axle F5-F6 to open dump door F7-F8 to lift dump body F-9-F10 to lift axles
Kenworth T800 sleeper Extended Flatbed tri axle F7-F8 for lift axle
Kenworth T800W sleeper toolbox tri-axle longframe F7-F8 for lift axle
Kenworth T800 Long frame Logtruck F5-F6 to open invisible door so the logs don't fall out. press K to view skeletal mode
Kenworth T800 Extended Flatbed tri-axle F7-F8 for lift axle
Kenworth T800 dump truck 2 axle F5-F6 to lift dump body F7-F8 to open dump door
Kenworth T800W Daycab heavy haul tri-axle shorterframe F7-F8 for lift axle
Kenworth T800 tilt Flatbed long frame Tri-axle F7-F8 to raise axle F9-F10 to raise bed F11-F12 to open tailgate
Kenworth T800 Tilt Flatbed regular frame F5-F6 to raise bed
Kenworth T800W sleeper heavy haul 4-axle heavyframe F7-F8 for lift axle
Kenworth T800W Daycab heavy haul 4-axle heavyframe F7-F8 for lift axle
Kenworth T800 tri axle boxtruck F7-F8 for lift axle
Here is a skin for the Kenworth T600 and a 2 axle tanker trailer. The skin is based off of fuel delivery trucks for HESS gas stations. I made the skin as close to the actual paint job as possible.
Credits:
Kenworth T600 - HemiBoy95 & Box5Diesel
Tanker Trailer - Trevor
Inspiration - My father
Skins - Venem (me)
Authors: sirendude 2011 and various members for support.
This is a pack of all of the vehicles I have made in the past 4 months. All of the cars are N/B only, don't have submesh, and some have no engine tuning.
none of these vehicles float, and one car (siren's auto 12x12 special) has all wheel drive, all wheel steer, working reverse lights, headlights, brakelights, and turn signals (flares). Some vehicles have opening hoods and doors.
Vehicles in this pack:
a 6x6 pickup truck called "mud slinger" (includes a Monster Truck version)
a 4x4 pickup truck simply called "pickup truck"
a few muscle cars/ sportscars (they are "highway terror", "lancia delta N/B Car", "tire burner", and "muscle car")
a school bus
a few offroaders ( they are "rock locker", "redneckrickem's dune buggy" (a YouTuber's buggy), "traxxurator"+"traxxurator dump" and "4x4 offroader")
a motorcycle (it has training wheels for stability :P)
and an engine that uses negative shocks to run, just give it a spin with the mouse and it runs. (be careful it explodes after a certain RPM)
You have the freedom to do whatever you want to these vehicles, but give me credits for the vehicle's N/B.
To open a hood or door, press F1 - F4. These commands do different things like open and close a door or hood.
These are re skinned trevors peterbilt 359s made to look like western star trucks. i am the skinner to a point, the skull on the side is part of a skin by "marco" so he gets credit for the skins also. i added all the rest. have fun.
Credit- Trevor- Trucks
-Platerpants"me"- skins
-Marco- skulls on skins
Features:
-Real weight, real power, real scale. (so don't expect to tow the ror trailers that way a kabillion lbs.)
-Lockers (press W)
-Operational dump bed, & tailgate
-Contactable bed to load vehicles or objects with ties (press O to tie down load)
-Animated winches on all except cargo version, some even have a rear winch.
-Flexbody everything pretty much
-Specular Shader
-Detailed Animated Interior with shifter.
-custom deuce sounds, with added turbo
Known issues:
-Shader shows up black sometimes, restart ROR until it appears normal, or download boring material below and drop in deuce zip.
-5th wheel version breaks when hooking to some trailers
-No flexbody tires (would be way to cpu heavy, it already is)
This pack has four custom Kenworth T600's. They started as a joke but I got carried away. There is probably a lot of bugs and stuff I haven't found but I just wanted to get them finished.
Most of the trucks are completely impractical. The wheel base is too long to have a tight turning circle. They sit so low you'll rip your bumper off the instant you hit a gutter. The lowriders with hydraulics have the worst ride imaginable and are stiff as a rock. The only purpose they really serve is to look cool.
Controls:
'L' to lock on a trailer
'N' for lights
'Ctrl+1' for headlights
'F4/F3' to raise and lower the hood
For trucks 2 and 3:
'F5/F6' for front hydros
'F7/F8' for rear hydros
Feel free to mod these or do your own bug-fixin' however you see fit.
Kenworth Transfer Dump Truck
A transfer dump truck inspired by a request on the forum.
Credits go to Box5Diesel for his Kenworth truck.
For information on how the system works see the request and showrooms thread.
Feel free to modify, but use a different unique id to make it not conflicting with my truck.
Skins for Box5diesels Kenworth should work on this truck, but I'm not sure.
I've fixed a little bug with the material of the trailer dump box.
aadcUID-W9000.zip
view details
Gold
Silver
Bronze
