|
|
|
Browsing tag Trailers, found 189 matching files. (38 pages)
|
(updated on 16/12/12)
|
Trailer P-32 is designed for quick transport wheeled and tracked vehicles and other material to the weight of 40 tons. In an emergency, up to 46 tons, maximum speed may be 10 km / h Is designed for off-set with tractor on roads I to III. class, the roads are paved and after tolerable terrain without external imbalances and obstacles.
Technical and tactical data
Dimensions:
- Total length (including shaft): 9475 mm
- Overall height: 1420 mm
- Height of the loading area: 1000 mm
- Overall width: 3100 mm
- Wheelbase: 4410 mm + 1000 mm
Loading area:
- Length: 4900 mm
- Width: 3100 mm
weights:
- Standby: 10,600 kg
- Payload: 40,000 kg
speed:
- The permissible maximum: 40 km / h
f1/f2 raids
forum link: P-32-Trailer
update: flexwheels nodes fix, frame model fix,
|
| |
|
|
 15 Comments, add comments here.
|
|
|
Liebherr 13HM mobile fast-erecting crane
All content is for use in Rigs of Rods only!
Use RoR 0.38.67+ for this!
Features
- Detailed meshes
- Accurate kinematics
- Realistic lifting capacity (refer to the board on the crane!)
Instructions
Start the engine and put the Crane in NEUTRAL!
- F1/F2: Rotate
- F3/F4: Trolley (use throttle to speed up if needed)
- F5/F6: Hook Up/Down (use throttle to speed up if needed)
- F7/F8: Extend/Retract Jib
- F9/F10: Raised-jib working angle
- Ctrl+F1/F2: Assemble/Disassemble
- Ctrl+F3/F4: Outriggers
- Ctrl+F5/F6: Legs
- Ctrl+F7/F8: Trailer wheel up/down
- Ctrl+F9/F10: Turn trailer wheel
- And as usual lock loads with "o"
You can also see the commands by pressing "T" ingame.
Basical procedure: Ctrl+F4 to fold outriggers; Ctrl+F6 once for legs, Ctrl+1 [NOT F1!] to display the baseplates, Ctrl+F6 again for legs. Then Ctrl+F2 to erect the crane automatically. Jib control is on F7/F8. Jib angle is on F9/F10. Retract automatically on Ctrl+F1.
Credits:
- sputnik_1: meshes, node and beam, sounds, textures
- BigBoy, Craneman, Lifter, Inviteds, Donators: testing and help, thanks a lot!
Support Thread |
| |
|
|
|
15 Comments, add comments here.
|
|
|
This is a large pack of custom light trailers for just about anything small.
CONTROLS:
Box Trailers - Ctrl+ F1/F2 = Open/Close Door
Cargo Trailer - Ctrl + F1/F2 = Lift/Lower Lid
TRAILER LIST:
Alpha Trailer "Basic" Factory
Flatbed Trailer "Basic" Factory
Flatbed Trailer "Extended" Factory
Flatbed Trailer "Lifted" Factory
Flatbed Trailer "Custom" Junker
Tandem Axle Trailer "Basic" Factory
Box Trailer "Basic" Factory
Box Trailer "Custom" Factory
Box Trailer "Lifted" Factory
Box Trailer "Custom" Construction
Cargo Trailer "Custom" Factory
TO MODDERS:
If you wish to mod this, just ask, I'm fine with it if you ask and give credit.
Link to Discussion: Flat-Bed-Light-Trailer-(Becoming-a-Mega-Pack!)
|
| |
|
|
|
10 Comments, add comments here.
|
|
|
Here is an inclosed bumper pull car trailer I made. The dimensions are: 7.62m or 25ft long, 3m or 9.8ft wide, and 2.4m or 8ft tall. Also it includes a .psd and .pdn texture map to make you own
texture. controls: CTRL + f1 & f2 = landing gear, CTRL + f3 & f4 = ramp
Credits
DODGE charger (me) = everything
Joebus = help with submesh
Please get permission before you release a mod.
Here it is hope you enjoy!
Discuss Here: Inclosed Car Trailer [RELEASE] |
| |
|
|
|
9 Comments, add comments here.
|
|
|
This is a Krone Box Liner container chassis.
It can carry 20' or 40' containers, compatible containers are in this pack:
http://www.rigsofrods.com/repository/view/4251
It can load 1x 40', 45' or 48' are also possible, but that may result in too much front and rear overhang and then the container might hit the tractor unit.
The other possibilities are 2x 20', 1x 20' in the middle or at the end with retracted chassis back.
You can extend and retract the rear end to fit different containers on, and it is possible to adapt the suspension to different heights and loads,
the command keys show up in the ingame preview.
There is also a version with two containers fixed to the trailer for people who don't bother loading or unloading it.
If you want to reskin it please use the GUID system and skinzip files, then you can upload your skins to the repo.
Don't modify anything else or use parts of it on other models without my permission please.
The truck is not included, but you can get it here:
http://www.rigsofrods.com/repository/view/3902
The map is not publicly released yet.
Feedback and comments:
Container-chassis
Thanks to tdev for the container skin and thanks to the beta testers and sorry that this project took over 4 years to be completed... |
| |
|
|
|
12 Comments, add comments here.
|
|
p-32.zip
view details
Gold
Silver
Bronze
