This pack is my attempt to capture the Streamline Moderne style popular in the 1930s and 1940s. The vehicles are all fictional, but their performance is realistic. I hope you'll enjoy driving them as much as I have enjoyed making them.
1948 Martin T64S "Custom" Tractor
A very low-slung 6x4 tractor. It has independent front suspension with double wishbones and load sharing rear suspension. The engine is a naturally aspirated 12-cylinder diesel driving through a 7-speed gearbox and locking differentials. Overall length is 29 ft, wheelbase 22 ft from front axle to centre of rear axle group, width 102 in, height 14 ft 9 in to tip of smokestacks. Kerb weight is 20,000 lbs, gross combination weight 80,000 lbs.
Fully loaded, the T64S will reach a top speed of 60 MPH with one of the included trailers. It will accelerate from 0-50 MPH in 1 minute, 0-60 MPH taking approximately 2 minutes.
1948 Martin O40 Tanker
A streamlined tank trailer in fictional "Hexaco" livery. Steel unibody, load sharing suspension. Overall length is 40 ft, wheelbase 28 ft from kingpin to axle group centre, width 102 in, height 10 ft 6 in. Loaded weight is 60,000 lbs.
1948 Martin F45 Flatbed
A simple flatbed trailer with stainless steel load deck and load sharing suspension. The deck is submeshed with the rollon flag and has ties to secure loads. Overall length is 45 ft, wheelbase 36 ft from kingpin to axle group centre, width 102 in, deck height 59 in, overall height 79 in to top of bulkhead. Kerb weight is 12,500 lbs, rated load 47,500 lbs.
1948 Martin V59 "Streamliner" Dry Van
A very large and somewhat impractical dry van. It has a streamlined stainless steel unibody and load sharing suspension. Overall length is 59 ft, wheelbase 47 ft from kingpin to axle group centre, width 102 in, height 14 ft 9 in. Loaded weight is 60,000 lbs.
Notes
These have only been tested in Rigs of Rods version 0.38.67.
The wheels have 40 nodes each, and the meshes were made in Sketchup. Don't expect these to be FPS-friendly.
The trailers are roll coupled via the system used by Lenni and Badboy for trailer steering. The centre of gravity and suspension are tuned accordingly; the trailers may topple easily on trucks that lack these nodes.
To minimise rolling resistance, the wheels are pushing the limits of the beam engine. They tend to oscillate when stationary. Caution is advised when stopping or parking on slopes as they may creep.
The trailers have very low drag. The T64S will not pull most other trailers at high speed.
Licence
CGTextures does not allow redistribution of its textures under open source licences. You must remove/replace their texture before releasing modifications of this truck. All other assets used are available for modding. See the readme for specific file information and licensing details.
This is a 1976 Ford W-9000 cab-over-engine semi tractor. A fairly basic node-beam vehicle that will get the job done. All of the pieces for this were created by me (M-138) except the mirrors. Feel free to modify, just remember to give credit.
This is a mod of the International4700_pack. The trucks are all 1998 International 4700s and are as follows:
5th Wheel (DT466E)
Gooseneck (T444E)
Flatbed (DT466E)
Long Flatbed (T444E)
Terrain Truck (DT466E)
Sounds were recorded from a 1998 International 3800 school bus (built from the 4700) with a 7.6L DT466E, and from a T444E engine
Credits go to dneufeld for the original International 4700 pack
Some bugs still exist like the front axle bending when turning especially since it only has 1 front axle now.
Credits:
Kuru for the N/B, Engine, Tool boxes & Fuel tanks
Lenni for the wheels
HRVI for making them
Any questions or what ever PM me or ask on here: Scania-142-Heavy-Hauler-Tipper-(Beta-First-Final-public-release)
Do not release mods without asking me via PM first!
This is it after a few months: the Seridon Si14 from Seridon Motorhomes
This is my first creation from scratch, and it's a bit oversized. The next versions will be better scaled
In the next update it is colorable
Credits:
Me: n/b and mesh
haselnut116601: support, door n/b and loads of other stuff
rainingheavy: steeringwheel and placement
Scalefreak93: shocks
Nickster 7: wheels
bray: engine settings
I don't remember all the people who helped me, so report it to me if I forgot someone!
Authors: sirendude 2011 and various members for support.
This is a pack of all of the vehicles I have made in the past 4 months. All of the cars are N/B only, don't have submesh, and some have no engine tuning.
none of these vehicles float, and one car (siren's auto 12x12 special) has all wheel drive, all wheel steer, working reverse lights, headlights, brakelights, and turn signals (flares). Some vehicles have opening hoods and doors.
Vehicles in this pack:
a 6x6 pickup truck called "mud slinger" (includes a Monster Truck version)
a 4x4 pickup truck simply called "pickup truck"
a few muscle cars/ sportscars (they are "highway terror", "lancia delta N/B Car", "tire burner", and "muscle car")
a school bus
a few offroaders ( they are "rock locker", "redneckrickem's dune buggy" (a YouTuber's buggy), "traxxurator"+"traxxurator dump" and "4x4 offroader")
a motorcycle (it has training wheels for stability :P)
and an engine that uses negative shocks to run, just give it a spin with the mouse and it runs. (be careful it explodes after a certain RPM)
You have the freedom to do whatever you want to these vehicles, but give me credits for the vehicle's N/B.
To open a hood or door, press F1 - F4. These commands do different things like open and close a door or hood.
These are re skinned trevors peterbilt 359s made to look like western star trucks. i am the skinner to a point, the skull on the side is part of a skin by "marco" so he gets credit for the skins also. i added all the rest. have fun.
Credit- Trevor- Trucks
-Platerpants"me"- skins
-Marco- skulls on skins
JensLynIV_streamliner.zip
view details
Gold
Silver
Bronze
